Pasco Fix Instructions

Pasco Fix can be used in many different types of applications.
Pasco-Fix can be used in many different applications, including industrial applications such as automobile plastics, sports goods, model building, photo and optical goods, and dental technology as well as many household consumer applications. Pasco-Fix adheres: wood, steel, aluminum, porcelain, glass, PMMA, rubber, hard PVC, ABS, Luran and all other common plastics – to themselves and to each other.

Pasco-Fix is not suitable for: cloth, paper, teflon, polyethylene and polypropylene. Note: for sticking polyethylene and polypropylene ask for our two special products, Pasco Prime and Pasco Pepp.

Pasco Fix Instructions for use :

Before gluing, materials should be cleaned with PASCO CLEAN, rubbing alcohol, or acetone (test on small area first) and allowed to dry. For strongly absorbent surfaces, somewhat more adhesive is needed. We recommend that you carry out some preliminary tests with PASCO FIX. Surfaces to be joined must free of rust, grease and dust. In some cases (e.g., leather), roughen the surface with fine sandpaper. Remove traces of old adhesive (scrape off). The thinner the layer of adhesive (spread on, don’t rub in) the better the joint. Allow the glued items to stand for a few minutes. Different materials dry at different rates. Best results are obtained at room tempera­ture. After 7-8 hours, any material will be firmly set. Always apply pressure when bonding, by squeezing or clamping the items to be glued.

Opening the container :
1. Unscrew the bottle.
2. Cut open the thinnest side of the bottle nozzle with scissors, with the smallest opening possible.
3. After use clean remaining glue off from nozzle with piece of cloth then screw cap on again.
4. Keep bottle in upright position.

Important note for storing Pasco®Fix:

We guarantee the stability of Pasco Fix for 1 year from the date of opening, provided that the bottle is kept cool and dry. It is HIGHLY recommended that you store Pasco Fix in a refrigerator for the longest shelf life.

Important !!! Light, heat and moisture are to be avoided.

PASCO FIX industrial adhesive is only available from authorized dealers, from trade fairs or directly from us. If you have any queries, please consult us. We will be glad to help you at any time.

Liability :

We decline all responsibility for any damage (including that to third parties) resulting from improper use or application of PASCO-FIX industrial adhesive.

Guarantee:

If, despite correct application, you are not satisfied with Pasco-Fix results, we guarantee to refund the full purchase price, on receipt of the opened bottle.

Cyanoacrylates: Danger !
Do not swallow. Do not inhale vapors. It may stick skin or eyelids tight within seconds. Keep out of the reach of children. Clean off hands with soap and water or hand-cleaner. Rinse eyes with special eyewash. Consult eye specialist.
Pasco ®Fix Industrial adhesives are available in 10g, 20g and 50g bottles. For industry and companies we deliver in any quantities.
Important note:
The specifications and recommendations given in this brochure must not be seen as guaranteed product characteristics. They are based on our laboratory tests and on practical experience. Since individual application conditions are beyond our knowledge, control and responsibility, this information is provided without any obligation. We do guarantee the continuously high quality of our products. However, own adequate laboratory and practical tests to find out if the product in question meets the requested properties are recommended. A claim cannot be derived from them. The user bears the only responsibility for non – appropriate or other than specified applications.

PASCO FILL ~ INSTRUCTIONS FOR USE:

Depending on the situation you may also put on Pasco®Fix first and then spread on Pasco®Fill The second variant proved most effective particularly at welds. Make sure that the filling material is soaked through well by Pasco®Fix. The hardened joint can be processed mechanically, filled in or varnished (lacquered). Pasco®Fill is not toxic. does not damage the environment and can be disposed of together with household waste. Pasco®Fix works as a “catalyst” for Pasco®Fill Put on Paso®Fill and soak thoroughly with Pasco®Fix. The stability of such an, usually impossible joint, can be obtained by using Pasco®Fill Knocked out or broken off materials can be refilled with Pasco®Fill and can then be fixed by putting on Pasco®Fix. In connection with Pasco®Fix, Pasco®Fill is most suitable to refill and replace broken off material of any kind. Pasco®Fill can be used for all materials such as porcelain, wood, steel, coloured metals, epoxies, ceramics, paper, cork, etc. The hardened surface can be processed mechanically.

Typical applications for Pasco Fix and Fill :

PascoFillApp1 PascoFillApp2 PascoFillApp3 PascoFillApp4

Important note:
The specifications and recommendations given in this brochure must not be seen as guaranteed product characteristics. They are based on our laboratory tests and on practical experience. Since individual application conditions are beyond our knowledge, control and responsibility, this information is provided without any obligation. We do guarantee the continuously high quality of our products. However, own adequate laboratory and practical tests to find out if the product in question meets the requested properties are recommended. A claim cannot be derived from them. The user bears the only responsibility for non – appropriate or other than specified applications.

Pasco®Fill, suitable as a filling material; in combination with Pasco®Fixit is used in applications like filling splitting, wood throats, punctures, joining and closing torn component rabbets and for many other applications more.

Put on shifts of Pasco®Fill of approx. 2-3 mm thickness and then impregnate thoroughly with Pasco®Fix.To prevent Pasco-Fill from dropping through holes, just put a sheet of paper underneath.